AMX APEX Destiny 6100 Dokumentacja Strona 27
- Strona / 84
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
27
TS16 - Only use between 32 - 127 degrees F
Temperatures from a TS16 can be used as a zone input. The system will prompt:
2 digit input number: The system supports up to 16 separate TS16s. Enter the TS16 address to be used. Legal
values are 1 - 16. Use the locations below to program the TS16. A temperature at or
above the High point is an open. A temperature at or below the Low temperature is an
open. The hysteresis setting determines how far the temperature must rise (above Low
setting) or fall (below High setting) for the zone to restore. TS16 inputs are not evaluated
for UL installation.
Options - Enter Total Location Value
Enable TS16
.......................................................................................................................
001
Speak all temperature transmissions
..................................................................................
002
Speak when time is requested
...........................................................................................
004
Open zone at High Temperature setting
............................................................................
016
Open zone at Low Temperature setting
.............................................................................
032
Hysteresis 2 degrees
..........................................................................................................
064
Hysteresis 4 degrees
..........................................................................................................
128
Default (TS16 disabled)
.....................................................................................................
000
Note: If a Low setpoint and High setpoint are being used then: Low + hysterics must be less then High - hysterics.
Hysterics settings of 2 and 4 can be added (192) for a hysterics of 6 degrees. If values 64 and 128 are not
used, the hysteresis is 1 degree.
Alarm Point Transmitters - Supervised
7 digit serial number: Enter the serial number listed on the bar code label. Only enter the seven numbers. The
leading letter on the label is not used.
Accept serial number: If the serial number is correct, press F2. Otherwise, press monitor and enter the correct
value.
The following is only prompted on multiloop transmitters:
1 digit input number: Use the transmitter loop locations to determine the input.
Loop 1
(Shock Input)
Loop 1
Loop 2
5816 (MN) 5817
Loop 3Loop 2Loop 1
5819
Loop 3
Loop 2
- DESTINY 6100 1
- Software Revisions 4
- Table of Contents 5
- System Options and Times 6
- Central Station Features 6
- User Codes 7
- Control Channels 7
- Specifications 8
- Inserting the Cabinet Lock 11
- Mounting the Control Board 11
- To House 12
- From Phone 12
- Wiring Notes 13
- System Terminals 14
- X-10 Interface Cord 16
- Program Mode 18
- Locations and Values 18
- Automated Locations 18
- Exiting Program Mode 18
- Programming 18
- Quick Start 19
- System Input Overview 20
- Programming System Inputs 20
- System Setup Example 21
- Using This Manual: 22
- Program a Zone 23
- Zone Questions 23
- * Zone Type 24
- Zone Options 1 24
- Zone Options 2 24
- Hardware Device Types 25
- Predefined Zone Assignments 25
- Hardwire Inputs 26
- 5816 (MN) 5817 27
- Button Type Devices 28
- Button Functions 29
- Editing Zone Programming 30
- Deleting a Zone 30
- Smoke Verification 33
- Speaker (Bell) Supervision 34
- RF Jam Detection 34
- System Options - Group 1 36
- System Options - Group 2 36
- System Options - Group 3 36
- System Options - Group 4 37
- System Options - Group 5 37
- System Options - Group 6 37
- System Access Codes 37
- System Times 38
- Monitor Trouble Conditions 38
- Bypass Options 38
- Phone Access Options 39
- Event Memory Log 39
- Communicator Times 46
- Two-Way Voice Options 46
- Two-Way Digit Assignments 47
- Report Codes 49
- Dialer Options 51
- Communicator Diagnostics 51
- User Communicator Test 51
- Central Station Terms 52
- Key Function Values 56
- Keypad Option 56
- Keypad Functions 57
- TS16 Group 1 57
- TS16 Group 2 57
- Keypad Area Assignment 57
- User Code + Digit Functions 58
- Extended Monitor Times 58
- Vocabulary 59
- Keypad Function Terms 61
- User Code Options 65
- Disappearing Code Activations 65
- Assigning User Codes to Areas 65
- User Code Terms 66
- Automation Overview 67
- Automation Example 67
- Channel Activations 68
- Control Channel Options 1 69
- Control Channel Options 2 69
- Control Channel Options 3 69
- Control Channel Options 4 69
- Control Channel Locations 70
- System Triggers 71
- X-10 Options 71
- Output Control Assignments 72
- Chain Group Assignments 73
- Control Channel Terms 74
- ADEMCO LIMITED WARRANTY 84
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa AMX APEX Destiny 6100
(18 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji