AMX NetLinx Integrated Controller NXI Instrukcja Użytkownika Strona 1

Operation/Reference GuideControllersNXINetLinx® Integrated ControllerInitial Release: / Last Revised: 1/8/2009

Connections and Wiring6NXI NetLinx Integrated ControllerIR/Serial Connections and WiringYou can connect up to eight IR- or serial-controllable devices

Programming7NXI NetLinx Integrated ControllerProgrammingThis section describes the Send_Commands, Send_Strings, and Channel commands you can use to pr

Programming8NXI NetLinx Integrated ControllerProgram Port CommandsThe Program port commands listed in the following table can be sent directly to the

Programming9NXI NetLinx Integrated ControllerProgram Port Commands (Cont.)PROGRAM INFO Displays the NetLinx program's name residing in the Master

Programming10NXI NetLinx Integrated ControllerESC Pass CodesThere are 'escape' codes in the pass mode. These codes can switch the display mo

Programming11NXI NetLinx Integrated ControllerNotes on Specific Telnet/Terminal ClientsTelnet and terminal clients will have different behaviors in so

Programming12NXI NetLinx Integrated ControllerRS-232/422/485 Send_CommandsRS-232/422/485 Send_CommandsB9MOFFSets the port's communica-tion parame

Programming13NXI NetLinx Integrated ControllerRS-232/422/485 Send_Commands (Cont.)SET BAUDSets the RS-232/422/485 port's communication param-eter

Programming14NXI NetLinx Integrated ControllerRS-232/422/485 Send_Commands (Cont.)RXONStarts transmitting received characters to the Master Card. This

Programming15NXI NetLinx Integrated ControllerRS-232/422/485 Send_String Escape SequencesRS-232/422/485 Send_String Escape Sequences27,17,Sends device

AMX Limited Warranty and DisclaimerAMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three

Programming16NXI NetLinx Integrated ControllerIR / Serial Ports (8 - 15) ChannelsIR/Serial Send_CommandsThe following IR and IR/Serial Send_Commands g

Programming17NXI NetLinx Integrated ControllerIR/Serial Send_Commands (Cont.)CTOFSets the duration of off time (no signal) between IR pulses for chann

Programming18NXI NetLinx Integrated ControllerIR/Serial Send_Commands (Cont.)PONTurns on a device, based on input Link. If at any time the IR sensor r

Programming19NXI NetLinx Integrated ControllerIR/Serial Send_Commands (Cont.)SPGenerates a single IR pulse. You can use the CTON to set pulse lengths

Programming20NXI NetLinx Integrated ControllerIR/Serial Send_Commands (Cont.)XCHMChanges the IR output pat-tern for the XCH command.Syntax:SEND_COMMAN

Programming21NXI NetLinx Integrated ControllerInput/Output Send_CommandsThe following Send_Commands program the I/O ports on the NXI.IR/Serial Send_Co

Programming22NXI NetLinx Integrated Controller

Programming23Enter the Document Name Here

1/09 ©2009 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without no

Table of ContentsiNXI NetLinx Integrated ControllerTable of ContentsProduct Information ...

iiNXI NetLinx Integrated ControllerTable of Contents

Product Information1NXI NetLinx Integrated ControllerProduct InformationThe NXI NetLinx Integrated Controller represents the new generation of AMX mul

Product Information2NXI NetLinx Integrated ControllerSpecificationsNXI SpecificationsPower requirements 1.09 A @ 12 VDC (NXI only/no card)Memory 64K o

Product Information3NXI NetLinx Integrated ControllerNXI Specifications (Cont.)Rear Panel Components:RS-232/422/485 (ports 1-6) Six 10-pin (male) conn

Product Information4NXI NetLinx Integrated Controller

Connections and Wiring5NXI NetLinx Integrated ControllerConnections and WiringInstalling the Master or Hub CardThe NXC-ME260 NetLinx Master or any Hub