AMX DTMF+ Interface AXB-DTMF+ Instrukcja Obsługi

instruction manualAXlink Bus ControllersAXB-DTMF+DTMF+ Interface

Configuration and Installation6 AXB-DTMF+ DTMF+ InterfaceTesting the AXB-DTMF+Follow these steps to test the AXB-DTMF+:1. Disconnect AXlink power.2. R

Programming7AXB-DTMF+ DTMF+ InterfaceProgrammingProgram the AXB-DTMF+ to send outbound DTMF codes using Axcess Send_Commands from the controlFine Tuni

Programming8 AXB-DTMF+ DTMF+ InterfaceOperative System Send_Commands (Cont.)Command DescriptionAUDIO-ON Enable audio from passing through the AXB-DTMF

Programming9AXB-DTMF+ DTMF+ InterfaceOperative System Send_Commands (Cont.)Command DescriptionDIAL-X-XXX-XXXX Dial number and send DTMF.• Spaces or hy

Programming10 AXB-DTMF+ DTMF+ InterfaceTiming System Send_CommandsThe following table lists the commands, which establish normal signal timing.The com

Programming11AXB-DTMF+ DTMF+ InterfaceTiming System Send_Commands (Cont.)Command DescriptionLOSSLCMIN-XXX The minimum time a loop current is off (used

Programming12 AXB-DTMF+ DTMF+ InterfaceTiming System Send_Commands (Cont.)Command DescriptionOREOFFMAX-XXX Outgoing reorder (fast busy) off time maxim

Programming13AXB-DTMF+ DTMF+ InterfaceTiming System Send_Commands (Cont.)Command DescriptionORIONMAX-XXX Outgoing ring on time maximum.• Time incremen

Programming14 AXB-DTMF+ DTMF+ InterfaceFine Tuning Send_CommandsThe following table lists the commands that fine tune AXB-DTMF+ signal timing. Most li

Programming15AXB-DTMF+ DTMF+ InterfaceDistinctive Ring Patterns and Send_CommandsDistinctive ringing is a service provided by the local telephone comp

AMX Limited Warranty and DisclaimerAMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three

Programming16 AXB-DTMF+ DTMF+ InterfaceChanging a Default Ring PatternChange a default ring pattern using the appropriate Send_Command when programmin

Programming17AXB-DTMF+ DTMF+ InterfaceDistinctive Ring Send_CommandsThe following Send_Commands are available for changing the default distinctive rin

Programming18 AXB-DTMF+ DTMF+ InterfaceAxcess Program ExampleTo program the AXB-DTMF+, you will need a personal computer with the Axcess software prog

Programming19AXB-DTMF+ DTMF+ Interface(* CONSTANT DEFINITIONS GO BELOW *)(****************************************

Programming20 AXB-DTMF+ DTMF+ InterfaceIF(STATE=2){ STATE=3 SEND_COMMAND DTMF_CARD,'OFF-HOOK' WAIT 20 'WAIT FOR DIAL TONE&apos

Programming21AXB-DTMF+ DTMF+ InterfaceIF(STATE=5){ PUSH[DTMF_CARD,34] (*OUTGOING_BUSY*) { CANCEL_WAIT 'WAIT FOR RESPONSE TO DIAL'

Programming22 AXB-DTMF+ DTMF+ InterfaceChannel CodesChannel codes on the AXB-DTMF+ are stored in memory (firmware) and process all outbound or inbound

Programming23AXB-DTMF+ DTMF+ InterfaceChannel Codes (Cont.)Operation Channel # Description (ON Indicates)Detection (Cont.) 39 Indicates a momentary lo

Programming24 AXB-DTMF+ DTMF+ InterfaceCaller IDThe AXB-DTMF+ provides report capability for receiving Caller ID information. The following table show

Programming25AXB-DTMF+ DTMF+ Interface(* THE DATA SHOULD APPEAR BETWEEN THE FIRST AND SECOND *)(* RING.

Table of ContentsiAXB-DTMF+ DTMF+ InterfaceTable of ContentsProduct Information ...

Programming26 AXB-DTMF+ DTMF+ InterfaceDEFINE_PROGRAMIF (FIND_STRING(DTMF_BUFFER,'CLID-',1)) (* START OF STRING FOUND *){ WAIT 20

Programming27AXB-DTMF+ DTMF+ Interface

AMX reserves the right to alter specifications without notice at any time.brussels • dallas • los angeles • mexico city • philadelphia • s

ii AXB-DTMF+ DTMF+ InterfaceTable of Contents

Product Information1AXB-DTMF+ DTMF+ InterfaceProduct InformationThe AXB-DTMF+ DTMF Interface (FIG. 1) links an Axcess central controller to a telephon

Product Information2 AXB-DTMF+ DTMF+ InterfaceAXB-DTMF+ Specifications (Cont.)Operation modes (set via internal jumpers):• Auto Answer• Line TypeRefer

Configuration and Installation3AXB-DTMF+ DTMF+ InterfaceConfiguration and InstallationSetting the Internal JumpersThere are two 2-position jumpers on

Configuration and Installation4 AXB-DTMF+ DTMF+ InterfaceLine Setting modeThe 2-position jumper JP1 selects PHONE or LEASED line operation when system

Configuration and Installation5AXB-DTMF+ DTMF+ InterfaceConnecting External Telephone LinesTelephone cabling for both the input and extension lines ar