AMX RDA-ENC2 Instrukcja Obsługi

instruction manualLighting ControlsRadia Lighting Control SystemControllers, Modules, and Cards

Installation6Radia Lighting Control SystemEnclosure DimensionsRDA-ENC2, -ENC4, and -ENC6 enclosure and dimensionsFIG. 4 shows the dimensions for the R

Installation7Radia Lighting Control SystemMounting AMX Lighting EnclosuresAMX Lighting enclosures must be mounted on a vertical surface with a minimum

Installation8Radia Lighting Control SystemConnecting high-voltage, single-phase input power and loadsFollow these steps to wire high-voltage (120 VAC,

Installation9Radia Lighting Control SystemRDA-ENC6B 120/240 VAC line input (single phase)FIG. 10 shows a 120/240 VAC single-phase (3 W + G) wiring dia

Installation10Radia Lighting Control System5. Connect load lines from the electrical devices to the Load terminals. Load 1 applies to dimmer 1, Load 2

Installation11Radia Lighting Control SystemRDA-ENC6 and RDA-ENC12 power distribution and line input referencesFIG. 14 shows the power distribution and

Installation12Radia Lighting Control SystemThe RDA-ENC2 enclosure contains a ground-terminating lug. The RDA-ENC4, RDA-ENC6, RDA-ENC6B, and RDA-ENC12B

Installation13Radia Lighting Control SystemModule connectionsWhen connecting a dimming/switching module to a AMX Lighting controller, connect as shown

Installation14Radia Lighting Control SystemGreen status LED indicatorWhen you apply power to the AMX Lighting Control System, the green status LED not

Installation15Radia Lighting Control System5. Apply power to the AMX Lighting controller at the breaker panel. FIG. 19 shows an example of how to inte

AMX Limited Warranty and DisclaimerAMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three

Installation16Radia Lighting Control SystemConfiguring and connecting AXlinkOn all AMX Lighting controllers, DIP switch SW1 sets the AXlink device num

Installation17Radia Lighting Control SystemEach contact closure connection (1 through 8) is pre-programmed with a default preset. The following table

Installation18Radia Lighting Control System4. Power up the controller enclosure and wait for the controller's green status LED to go off after ap

Compatible Ballast Information19Radia Lighting Control SystemCompatible Ballast InformationThis section contains descriptions and manufacturer informa

Compatible Ballast Information20Radia Lighting Control SystemBallast Interfaces and 2-Wire BallastsIn some cases, dimmers are wired to ballast interfa

Glossary21Radia Lighting Control SystemGlossaryAir Gap Switch - A relay or mechanical switch that physically separates a load from the power feed, res

Glossary22Radia Lighting Control SystemControl Current - The current used by a dimmer or switch to perform its function. Each Radia Lighting controlle

Glossary23Radia Lighting Control SystemIntegrated Dimmer Module - A Radia Lighting device that contains both a six-channel master controller and dimme

Glossary24Radia Lighting Control SystemPreset Fade Time - A Radia Lighting default parameter. The amount of time it takes for one preset to begin to

Glossary25Radia Lighting Control System

Table of ContentsiRadia Lighting Control SystemTable of ContentsIntroduction ...

AMX reserves the right to alter specifications without notice at any time.043-0042592 6/04 ©2004 AMX Corporation. All rights reserved. AMX, the AMX

iiRadia Lighting Control SystemTable of ContentsGlossary ...

Introduction1Radia Lighting Control SystemIntroductionThe AMX Radia Lighting Control SystemTM employs a dual-platform programming architecture that su

Introduction2Radia Lighting Control SystemApplicationsYou can use the AMX Lighting Control System for commercial, corporate, and residential applicati

Introduction3Radia Lighting Control SystemAMX Lighting Control EquipmentThe following table lists all of the AMX Lighting Control System equipment. Re

Introduction4Radia Lighting Control SystemAMX Lighting Control Equipment (Cont.)Dimmer modules (Cont.)RDM-MDM Multimode dimming module (2400 W/20 A)RD

Installation5Radia Lighting Control SystemInstallationSpace RequirementsAMX Lighting control installations require very little space. Enclosures are t